You must log in or register to comment.
My 0$ knobWhy not both. 3D print one and swap them at Home Depot. Or heck 3D print all of them, replace them all, keep the one you need and sell the rest on eBay. If they all match, I doubt Home Depot would even notice.
Some poor sucker is going to eventually buy the display model tho
They’ll get an even better deal then given the missing knobs! Or the store will just foot the bill for the replacement knob that they can probably get for less than the consumer price
Well they’re available on eBay…
You can dip it in shiny paint too. Its not stainless steel but its good enough
No worries, the OEM ones aren’t stainless steel, either. They’re “stainless appearance,” i.e. plastic with a thin veneer of cheesy chrome plating that’s about one molecule thick.
You can electroplate 3D prints by using a basecoat of conductive spraypaint, and then the limit of the thickness of your plating is only really limited by your patience. Nickel is quite easy to do at home.
I quite like electroplating with titanium. Can vary the voltage for some great colors too.
I feel like this parallels the story about spending of $10 million to research and develop a Space Pen vs just using pencils.
The problem with pencils is that in space broken graphite floats around easily and is conductive. A conductive powder floating into something electronic in a pressurized oxygen rich environment is no bueno.
Graphite powder is also quite flammable isn’t it?
I’m not sure, but with that much oxygen in the air I’m sure anything could “become” flammable, especially when atomized or turned into a powder. That’s why grain silos on farms are fire hazards; the dust.
Not that BS story again…
Had to read like 50 comments and nobody pointed out you can just buy a generic knob for like $1. Hell your used building center would be 50 cents. WTF world do we live in where the solution is CAD and 3D printing for something so trivial. It’s like using a nuclear bomb to kill an ant nest.
Look dude, fuck those ants.
Once you have the printer and the knowhow, it takes like 5 minutes to draw and 20 minutes to print at a cost of like 0.10 €
It takes longer to go to a location and buy it at a much higher cost. So why should you?
Its also something you built with your hands and brain. There are few things which feel as good.
Oh yes! The correct answer is to 3D print a plastic knob for the front of an oven. There’s not going to be any heat issues there! And no one can deny how beautiful that black knob looks next to the brushed metal.
The knobs on your oven are overwhelmingly likely to be either completely made of plastic or contain a large percentage of plastic already. Typically they’re made of ABS or PBT.
PLA probably isn’t a good choice for this application but you could absolutely print some knobs in ABS or ASA and you’d be fine. You can even get PBT filament, but that’s probably more hassle than it’s worth and ABS is cheaper.
There is no single correct answer. There often isn’t, in fact.
As for heat: You can treat PLA to be more resistive to temperature and even at stock, untreated, cheapest PLA wont just deform from hot air escaping since the thing melts at 190 and the air wont be that hot for long enough. It may deform with regular use though. You also don’t have to use PLA and use something more temp resistive.
Beauty? Eye of the beholder. Its a conversation piece. Its something you point at and say “I made that”. Its wabi-sabi, I like it.
190 celsius, I’d like to add.
If it melts, just print another!
The stock knobs are most likely plastic already, but I do agree the black knob looks stupid. It would probably look a lot better to print matching replacements for all of them.
With free returns and having a size difference in my feet I may (or may not) order 2 different sizes of the same shoe and end up returning one.
The same but for my broken Xbox, after a little sticker art.
While I don’t do it myself, I don’t consider stealing from big name stores theft and am, actually, completely morally fine with it. Will not report somebody stealing even if I see them.
The day big corporations stop stealing from the workers is the day I care about stealing from them. That day will not come.
Let’s not forget the rampant wage theft across the entirety of the US, much less the ongoing grift they’re pulling on its citizens re: “shoplifting”, etc. being the big scary Evil — when wage theft stats completely destroy the charts in comparison to all other commercial/consumer theft, including misappropriation by employees! 😡
TL;DR: Stealing from big corps isn’t theft. It’s a civic duty, at this point.
LG wants me to pay $45 for a single official replacement.
Amazon has a whole set for $14.
Both are appropriate responses to the bullshit that is oven knobs.
You can save so much money with CAD if you neither factor in your time to actually learn it or the cost of the printer itself.
Makes crime even better in comparison.
The saving on the knob alone would pay a reasonable chunk of a basic but useful printer. Use it for a few more things and you’ll be in the black even ignoring the more fun things you might do. The time it takes to learn a CAD system can also be fun if you enjoy that sort of thing.
I’m proof. My first printer is currently worth like $25. Maker Select V2. Still works great. I learned FreeCAD and enjoyed every minute.
As someone who replaced his Maker Select Plus with a Bambu Lab P1S a few months ago…if you do get a new printer, be prepared to be angry for a moment.
I spent so much time and effort improving that thing over the years, and the modern printer was so much better right out of the box. 😅
(Not that I don’t still have a fond place in my heart for my old bedslinger. A friend has it now, so it’s still chugging along.)
Haha yea I did, actually. A few months ago I built a Voron 0.2. It’s soooo much better in every way. But the MS2 is still capable, especially with upgrsdes (just not with ABS). I decided against the Bamboo route because I loved the FOSS nature of the MS2, and building the Voron brought back those ‘first time building a PC vibes’. It was a great experience.
I’ve got a Sovol Max on order, so the MK2 will probably also be donated to a friend this year.
Nice! I’ve considered a Voron, but I wasn’t sure I wanted to dedicate that much time to the printer as opposed to the printing. (I feel like I got my fill of excessive tinkering already 😅)
But the closed nature of Bambu does bother me, I’ll admit.
Yea, I was told I “have a 3D printer hobby, not a 3D printing hobby”. 😆
I loved building the Voron, but did decide to go with a Sovol instead for the larger machine to both avoid the build and have a larger volume.
The 0.2 was great because it was cheap, didn’t need to be my main printer at the time so I could be patient with it, and it is blazingly fast, especially heat up time since the bed is so small.
compooter + printer still go brrrrrrrrrrr
More of a brrrrr zoop zoop eeeeeeep save me brrrr doop ding please zrrriiippp scooop
Learning a new and useful skill is not “wasting” time at all.
You can’t put that in quotation marks like I ever said something about wasting time. You just have to include all that time in your cost calculation.
Not really, no. If you’re learning something not only that you like, but that it’s also useful and that you will you use many times in the future, I wouldn’t consider that to be part of the “cost”.
Someone else I know got a printer and got bored printing with it after a bit and said I can print on it whenever if I toss them a roll of material every now and then.
I ended up finding all kinds of useful things to print. I made a connection piece for a sink that had a garbage disposal removed when I couldn’t find the fitting anywhere and after 3 years it’s holding up fine. I made a set of cams for a washer that randomly stopped spinning one day and those have been working nicely. Just a bunch of times it ended up coming in handy.
Here in Canada every major library I’ve been to has a 3D printer you can use, either for free if you bring your own filament, or for a very small fee to use theirs. I live in a small town of 70,000 people and our public library has a 3D printer.
I would just like to say that 70k people isn’t a small town. I live in a town with 9k people in it. Now that’s a small town.
Only 9k people? That’s not a town, that’s a village.
/s
9k? That’s a major city. I lived and worked in an area where the 9k town about an hour away was the bee’s knees for the folks where I was, which had a great!!! city of 2,500, and the rest were unincorporated places of a hundred or so at the crossroads.
Shoot, I just moved to town under 1k.
My printer has saved me more than its cost in useful stuff I have printed.
I have wasted a bunch of time making things, but like woodworking or similar trades, it’s fun and rewarding.
Hence, why it’s not “wasted” time.
There are places which will print out your model for a small fee on their own printer. There are even places which will allow you to use their printer if you come with your own filament (for example makerspaces) and maybe donate a little bit to support them.
As for CAD itself, there’s a nonzero chance that someone already designed that part for themselves and you can download a ready model. If not, then by designing it yourself you’re acquiring a skill that can be useful again in the future and you can share that model with others to get that warm fuzzy feeling that you’ve helped strangers who had the same problem.
My printer has saved me more than it’s cost in useful stuff I have printed.
I’d like to take this opportunity to say sorry to all the people that ended up buying the WD-40s I stole the straw off of.
Man, i mean while we’re fessing up to these things…
If you bought a PC gamer magazine from Barnes and noble back in like 2004 and the demo disc was missing, I’m so sorry.
Oh, are we confessing to
minorthefts? Let’s see, what’s beyond 7 years old…A Hogwarts robe clip from a Halloween costume
$12 in expired powerbars
About $200 in assorted mediocre liquor from some wedding
4 posters from bus stops for the Scooby-Doo movie
A 1999 Ford Explorer
7 Playboys and a bag of old coins
97 million kisses from my missus
(Edit: the largest thefts are the kisses)
I’m telling the missus that you think her kisses are only minor theft worthy!
At scale, it’s a felony, I promise!
I used to shoplift handheld electronic games, stuff like Electronic Quarterback by Coleco. I was a paper boy and I would walk into stores with my bag around my shoulder and just grab games off the counter and slip them in the bag. What blows my mind now is that this was even possible - this was the late 1970s and apparently I was something of an innovator because the stores never suspected anything or searched kids, and the electronic games were just sitting out on counters. It wasn’t long after this that stores started only allowing two kids into the store at a time and shit like that, and searching them when they left.
You’re welcome, subsequent generations of would-be shoplifters! You’ll never know just how fucking easy we had it.
A Hogwarts robe clip from a Halloween costume
Shame on you
I once ate the baby carrots from the grocery store, right off the display. I am not sorry about it.
I don’t think there’s anything in that story to be sorry about.
There is, you need to wash vegetables before you eat them
I’m pretty sure baby carrots are prewashed.
Edit: Oh, perhaps you don’t know this. In which case, I’d love to be the one to tell you: baby carrots are just cut up regular carrots.
Even if they’re prewashed, they’re lying in a crowded supermarket on display all day. You don’t know who touched them and who sneezed on them, but you can know for a fact, someone did, and most people don’t wash hands.
I learned this from my dad… When I was young, we had a plumbing leak on a Sunday night, p-trap was leaking. All places were closed, so he went to a McDonald’s bathroom and stole theirs to replace ours.
20 something years later, my faucet was leaking. It was a discontinued model from a brand owned by home Depot, though they still had the display model up. Remembering what my pa did, I took the display model apart and took what I needed.
lmaooo that’s why bathrooms in those places now have the minimal setup to work properly. Good to know that I can be part of the change.
From this story alone I have several ideas of what your accent is, also this is the type of shit my kin would pull. I’m more of a "how many parts can I daisy chain while maintaining no leakage, my record is 12 which was the minimum needed. I hope an actual plumber never looks at my bathtub plumbing cause the faucet is certainly doing things much like my computers cable management.
I am interested in what you assume me accent be, though I’ll give ya some hints and you tell me where I’m from…
My wife teases my pronunciation of butter and water as they come out as “budder” and “wooder”, house roofs as “woofs”, and I call water creeks “cricks”. She also laughs at me when I get angry \ passionate as I become louder and sound like “one of those Italian gangsters from the old bugs Bunny cartoons”. And she’ll repeat back to me, exaggerated, “whaddya talkin about?!” as I seem to ask her that before every debate…
Well initially I was gonna guess North Eastern Coastal, or perhaps some of the less known accents from Western Appalachia but I’ve known folks from around Bakersfield who pronounced water, butter, and creeks like ya so I ain’t got no fucken clue. It’s one of those things where its got overlaps with but not totality with accents I do know, even my own accent does the budder thing. But now I ain’t so certain.
Philadelphia! Very astute, my friend. Where are you yourself?
I somewhat thought that getting an education, working white collar, social media, and living in Europe the last 6 years that I would have of lost my accent. Hence why I found your comment so interesting!
SoCal more specifically Inland Empire San Bernardino foothills.
Also your accent stay with you hell it can even stay with your kin depending on various factors. My accent is basically just an old regional accent but if I get pissy enough it rapidly devolves into a bastardized brogue. But yeah I find dialects and accents interesting especially in how they mutate diverge and reconverge.
Also if you are at all curious I pronounce it budder, wader, and rooves.
Why are people breaking/losing knobs on their ranges in the first place? I’ve never done that in 4 decades. Seems like an extremely unlikely thing to do.
I would have said the same thing but the enshitification isn’t just for the web anymore - I had a ‘quality’ name brand refrigerator and snapped the drawer down the front because I pulled on it a little too hard. Those things used to be bulletproof but now they’re flimsy crap.
Yep happen to our fridge. Not mention it quit working after 2 years of use. Now buy mine off FB market place. Why bother buying new.
Enshittification is probably a large part. However, I can see it.
Our’s are plastic, 25 years old, and look like crap. Wash them all you want, they just look dirty all the time. I’d replace them except for the absurd cost for a piece of molded ABS.
I take them off to wash them. I can imagine someone having an accident with one, like washing them in dishwasher and having one fall down onto a heating element. Those are big, but our’s are small enough to get knocked down onto the garbage disposal - it would’t be easy, and would require an unusual sequence is events, but I’ve fucked up even more unlikely sequences of events in my life.
I really wish I could get decent aluminum replacements for our’s; it wouldn’t make the range any newer, but it’d make it look nicer than the black plastic shit that it came with.
Aluminum casting is fun and cheap.
I know my limitations. One of them is patience.
I was thinking the same thing? Who are these animals that somehow destroy a metal knob on a commercial-style $8000 Bosch oven that is made of stainless steel?!
My only guess is that they have children who steal the knobs and flush them down the toilet or something. But the knobs on those high end models are pretty huge which means they would probably get stuck and refuse to flush down.
Those knobs probably aren’t metal, but plastic with a metal plating.
If I paid the obscene amount of money that those things cost I’d be mad as hell if the knobs were made of fucking plastic.
People with toddlers often keep the knobs off as a form of baby proofing, when the kiddos are tall enough to reach but not old enough to listen. It’s then easy to lose a knob that isn’t in the right place.
I completely forgot until now that my daughter used to steal the knob from our dishwasher on a near daily basis. I remember confiscating it one morning and accidentally bringing it to work in my pocket.
Oh, that’s brilliant! I guess its better to lose it all together than to give a toddler access to fire/a really hot thing
Yep. They also sell childproof knob covers for them, you have to pop open the lid to reach them.
I’m embarrassed it took a few times of the toddlers walking off with the knobs inside the covers before we realized we could just… not leave the knobs on. I blame the fact that they never slept more than 90 minutes at a time…
I think if you have young children you shouldn’t have a high end range like this (especially gas). A standard range with the knobs at the back where they’re much harder to reach would be a lot safer.
Sometimes people have kids after moving into a place/buying things, too.
Some guy once broke into my brother’s backyard and stole the lid to his BBQ. Just the lid.
Sounds like a tweaker preparing to join a Roman Phalanx
Gods spread Romaboo tweaker!
You can accidentally hit a knob and break it while moving the appliance itself. As for losing them, sometimes you knock one loose and it rolls under the fridge, and it’s not worth the effort of moving a large appliance out of its nook just to get the knob back. Shit happens.
Maybe you were just a miracle child who never has accidents. Who knows?
I have never had a range where the knobs are at the front, so that’s probably part of it. They’re much safer at the back.
Ours is a cheap model, but the knobs are held on with a plastic housing inside the knob similar to that middle plastic tube that holds keycaps center on keyboards. Im constantly worried its going to break when i take them off to clean.
Kinda depends on your environment, a lot of plastics are susceptible to degrading in certain temperatures, humidity levels, or especially from being left in direct sunlight.
I recently re-did my kitchen floor with 1’ square peel-and-stick vinyl tiles. After buying four boxes (30 tiles each at $45 a pop), I ended up exactly one tile short. I was sorely tempted to go back to Home Despot and slip one tile out of a box - obviously people do this a lot there since there are always open boxes in the tile section. In the end I just pieced the last tile out of scrap bits, in a spot where it really wasn’t obvious. I don’t need a fucking shoplifting charge at this stage of my life.
I like this because then the display is broken in the same way it will actually break when someone buys it. It’s like warning others of the issue. It’s really a public service when you think about it lol
Maybe that’s what happened to the original knob. Years ago someone bought a stove and the knob broke so they stole their neighbours as a replacement, thus starting a tit for tat, reciprocal crime wave that swept the nation.
That’s actually hilarious, i never thought about that when i see missing parts in stores.
