Fun fact: that’s not how humidity works. It, in fact, DOES help to get water to evaporate by forcing the local humidity around the phone to stay low. Otherwise you may as well say all the people doing 3D printing that use desiccant to keep water out of their filaments are fools, too.
What it won’t do is magically erase any gunk or minerals that were in the water that can short out traces on unprotected PCBs and chips even with the water gone.
So, yes, it is not magic that can fix any phone that saw water. Though it absolutely helps to get the water out of the phone. … I mean, unless you live in a desert where the humidity should already be sufficiently low most days.
It makes it awful for the purpose of drying wet electronics. It actually impedes the drying process by preventing air from circulating. Plus rice is typically dusty, and you don’t want rice dust in your damp electronics.
You’ll have a dryer device much faster if you just point a fan at it.
I have a mason jar full of the desiccant packets that come with the random crap I order. I hang on to them in case my phone decides to go swimming. I recommend it to people, but I don’t think I’ve made many converts lol
Just remember that dessicant (including rice) should be dried out in the oven if you’re going to expect it to drop humidity below normal ambient humidity. Obviously not baked, but a few hours at ~180F to ~220F will dry out most dessicants. Some are really hydrophillic, though, and might take even higher temps.
Usually the kinds that dry out at lower temps are labeled as reusable or similar terminology. (unless it’s a disposable packet, then it’s what ever the hell they decided to throw in there).
Shit I just dropped my phone in the sink! Just give me a minute to hop online… Commercial grade desiccant… 7-10 days shipping… Buy now… Great! In a week I’ll have the driest phone ever!
Dealing with humidity is one thing, but it’s terrible at drawing “whole” water out of something.
And it’s not the water that’s the problem, it’s like you said, it’s the gunk and minerals it leaves behind.
Isopropyl alcohol will push water out of any cracks and crevices, if you’re able to submerge bare boards in it. If you do it before the minerals have a chance to dry and corrode, it will get pushed out with the water.
Again untrue whatever you think is “whole” water, any dessicant will absolutely undoubtedly help with evaporation.
Not every person is tech savvy enough to open boards. Advice for most novices is still put phone between dessicant to get water out of the device is valid and good advice.
Would using isopropyl alcohol be better option? Sure it is. but telling my aunt to do it, and device will probably die because she doesn’t know how to handle pcbs anyway. I’d much rather just advice using dessicant and hope mineral residue doesn’t sort anything. And I’ll continue with that advice forever.
Fun fact: that’s not how humidity works. It, in fact, DOES help to get water to evaporate by forcing the local humidity around the phone to stay low. Otherwise you may as well say all the people doing 3D printing that use desiccant to keep water out of their filaments are fools, too.
What it won’t do is magically erase any gunk or minerals that were in the water that can short out traces on unprotected PCBs and chips even with the water gone.
So, yes, it is not magic that can fix any phone that saw water. Though it absolutely helps to get the water out of the phone. … I mean, unless you live in a desert where the humidity should already be sufficiently low most days.
Sure, but rice is a shitty desiccant. If it weren’t, it would cook easier and we would ship things with packets of rice rather than silica gel.
Silica gel is a great desiccant. Just because rice cannot match something basically designed for the task, doesn’t make it awful.
You might as well be saying, “but my horse cannot run fast! He’s always behind Secretariat!”
It makes it awful for the purpose of drying wet electronics. It actually impedes the drying process by preventing air from circulating. Plus rice is typically dusty, and you don’t want rice dust in your damp electronics.
You’ll have a dryer device much faster if you just point a fan at it.
It may not be an industrial-grade desiccant, but the major advantage of rice is that people tend to have it at home…
I have a mason jar full of the desiccant packets that come with the random crap I order. I hang on to them in case my phone decides to go swimming. I recommend it to people, but I don’t think I’ve made many converts lol
Just remember that dessicant (including rice) should be dried out in the oven if you’re going to expect it to drop humidity below normal ambient humidity. Obviously not baked, but a few hours at ~180F to ~220F will dry out most dessicants. Some are really hydrophillic, though, and might take even higher temps.
Usually the kinds that dry out at lower temps are labeled as reusable or similar terminology. (unless it’s a disposable packet, then it’s what ever the hell they decided to throw in there).
I didn’t know that, thanks!
Shit I just dropped my phone in the sink! Just give me a minute to hop online… Commercial grade desiccant… 7-10 days shipping… Buy now… Great! In a week I’ll have the driest phone ever!
Good point. I’ll use diatomaceous earth next time.
Dammit - now I’m cringing at the thought of datomaceous earth in the USB port!
Is this how I debug my phone?
Dealing with humidity is one thing, but it’s terrible at drawing “whole” water out of something.
And it’s not the water that’s the problem, it’s like you said, it’s the gunk and minerals it leaves behind.
Isopropyl alcohol will push water out of any cracks and crevices, if you’re able to submerge bare boards in it. If you do it before the minerals have a chance to dry and corrode, it will get pushed out with the water.
Again untrue whatever you think is “whole” water, any dessicant will absolutely undoubtedly help with evaporation.
Not every person is tech savvy enough to open boards. Advice for most novices is still put phone between dessicant to get water out of the device is valid and good advice.
Would using isopropyl alcohol be better option? Sure it is. but telling my aunt to do it, and device will probably die because she doesn’t know how to handle pcbs anyway. I’d much rather just advice using dessicant and hope mineral residue doesn’t sort anything. And I’ll continue with that advice forever.
But it doesn’t help with evaporation. It actually prevents it by preventing air from circulating.