I wish someone pointed this out 20 years ago (enough to be heard). I raised two kids with occasional asthma in a house with gas stove, and maybe that could have been different.
I recently converted from gas to induction, and find it a much better cooking appliance in every way. Pans on the stovetop heat up faster than with gas, and I can boil a pot of water faster. The oven has more options and more consistent heating, especially on the broiler.
The only problem was the cost. Way too much money to get a new circuit installed but also the range was double or more what I would have spent on gas. There were very few options at appliance stores, and I never did find one on display, of any brand. In the US, it’s unnecessarily difficult to make this switch.
When I was shopping for one I was told to pay attention to coil sizes. Sure enough experimenting with a large skillet on small coil shows very uneven heating. I did find one or two reasonable priced ranges but with only tiny coils. Even at spending way too much, I only have one coil that works well with 12” skillet or stock pot. I know ikea now sells an induction range for more reasonable price but coil size is critical and the first thing I’d look at
Having a proper exhaust hood that sucks air outside mitigates this to a huge degree, but a lot of us have hoods that “filter” the air through nothing and then shoot it up towards the ceiling.
The flippers who did my house disconnected the outside air vent, I’m still pissed and mean to get it fixed, cause I can’t afford an induction range either.
If you think you can’t afford an induction range, you also can’t afford to hire contractors to have your new ductwork put in and/or unborked.
Much as I hate to recommend Frigidaire for various reasons, the FCFI3083AS is I think the most economical freestanding 30" induction range on the market at the moment and has an MSRP of $1099. You can probably score one from some discount or independent appliance retailers (i.e. not Home Depot, Lowes, or Best Buy) for a little under a thousand.
As a taller guy who wears glasses, I’ve had the horrible experience of some of these filters blowing greasy air in my face and settling on my glasses. Not pleasant
Mine has a vent, but no hood so there’s only so much it can do. And the way they built out the kitchen means there’s no good way to install a hood without remodelling.
But now I don’t care as much. The current vent (and window) is good enough for induction
It’s a failure to read the manual thing. Every OTR microwave ever manufactured functions as a hood by definition, and basically all of them (I can only think of like two exceptions) have the option to be configured for either recirculation or to duct outside. It’s just that most models come out of the box already configured for recirculation and most people ('s contractors) are so averse to reading that they fail to realize you can flip the blower motor over and thus cause it to actually accomplish something (provided a duct is in place) rather than just blowing stale air back in your face.
The ducting behind a microwave is not that common in my experience. It makes sense for microwaves to come preconfigured to recirculate instead of trying to exhaust to a sheet of drywall because most people are going to install it how it comes out of the box. I’ve installed dozens of microwaves and only twice has ducting existed to flip the venting for. Higher end houses typically have dedicated exhaust fans and lower end houses never seem to have ducting for a microwave. I installed a dedicated fan that exhausts out the roof at my house. Even with ducting those microwave exhaust fans barely provide anything of value. I’m sure my experience is very regional but it seems like a really niche middle ground where someone would bother venting out of the kitchen but also not care enough to have a purpose built exhaust fan.
Part of the problem there is I have guys just absolutely insist at me that a microwave “can’t” be vented outside so they don’t bother to install a duct, and tell me that in order to vent outside you “have” to get a hood instead. This is obviously bogus.
This also leads to the inevitable Contractor Special where a duct was there, often when the user is replacing an old hood with a microwave, but the installer just shrugs and slaps the microwave on the wall as-is where A) it is inevitably too tall and now way too close to the stovetop, and B) covering the duct outlet while still recirculating back into the room. Whenever I unearth one of these in my travels it makes me want to track down whoever the hell installed it and then punch them so hard they come clean out of their socks.
People are for some reason hyperfixated on getting appliances off of their countertops, which is why the over-the-range microwaves became so prevalent in the first place. (And then they all immediately filled the spot where their countertop microwave used to be with a countertop air fryer instead, but that’s a whole different discussion.)
Yeah that would drive me insane to run across. It’s not even particularly hard to tell that the exhaust fan motor is reversible just by looking at the top/back of the microwave before it is installed. Every one I’ve seen looks pretty damn modular in comparison to the rest of the microwave shell.
Edit: reversible is the wrong word, able to be unscrewed and rotated, I’m sure you know what I meant but on a reread of my comment I wanted to clarify.
I wish someone pointed this out 20 years ago (enough to be heard). I raised two kids with occasional asthma in a house with gas stove, and maybe that could have been different.
I recently converted from gas to induction, and find it a much better cooking appliance in every way. Pans on the stovetop heat up faster than with gas, and I can boil a pot of water faster. The oven has more options and more consistent heating, especially on the broiler.
The only problem was the cost. Way too much money to get a new circuit installed but also the range was double or more what I would have spent on gas. There were very few options at appliance stores, and I never did find one on display, of any brand. In the US, it’s unnecessarily difficult to make this switch.
When I was shopping for one I was told to pay attention to coil sizes. Sure enough experimenting with a large skillet on small coil shows very uneven heating. I did find one or two reasonable priced ranges but with only tiny coils. Even at spending way too much, I only have one coil that works well with 12” skillet or stock pot. I know ikea now sells an induction range for more reasonable price but coil size is critical and the first thing I’d look at
I have gas and would fight anyone who tries to tell me otherwise. I rented a place with an induction range and now I want one so bad.
Having a proper exhaust hood that sucks air outside mitigates this to a huge degree, but a lot of us have hoods that “filter” the air through nothing and then shoot it up towards the ceiling.
The flippers who did my house disconnected the outside air vent, I’m still pissed and mean to get it fixed, cause I can’t afford an induction range either.
If you think you can’t afford an induction range, you also can’t afford to hire contractors to have your new ductwork put in and/or unborked.
Much as I hate to recommend Frigidaire for various reasons, the FCFI3083AS is I think the most economical freestanding 30" induction range on the market at the moment and has an MSRP of $1099. You can probably score one from some discount or independent appliance retailers (i.e. not Home Depot, Lowes, or Best Buy) for a little under a thousand.
As a taller guy who wears glasses, I’ve had the horrible experience of some of these filters blowing greasy air in my face and settling on my glasses. Not pleasant
Mine has a vent, but no hood so there’s only so much it can do. And the way they built out the kitchen means there’s no good way to install a hood without remodelling.
But now I don’t care as much. The current vent (and window) is good enough for induction
Everyone I know has a microwave. Is that a class thing?
It’s a failure to read the manual thing. Every OTR microwave ever manufactured functions as a hood by definition, and basically all of them (I can only think of like two exceptions) have the option to be configured for either recirculation or to duct outside. It’s just that most models come out of the box already configured for recirculation and most people ('s contractors) are so averse to reading that they fail to realize you can flip the blower motor over and thus cause it to actually accomplish something (provided a duct is in place) rather than just blowing stale air back in your face.
The ducting behind a microwave is not that common in my experience. It makes sense for microwaves to come preconfigured to recirculate instead of trying to exhaust to a sheet of drywall because most people are going to install it how it comes out of the box. I’ve installed dozens of microwaves and only twice has ducting existed to flip the venting for. Higher end houses typically have dedicated exhaust fans and lower end houses never seem to have ducting for a microwave. I installed a dedicated fan that exhausts out the roof at my house. Even with ducting those microwave exhaust fans barely provide anything of value. I’m sure my experience is very regional but it seems like a really niche middle ground where someone would bother venting out of the kitchen but also not care enough to have a purpose built exhaust fan.
Part of the problem there is I have guys just absolutely insist at me that a microwave “can’t” be vented outside so they don’t bother to install a duct, and tell me that in order to vent outside you “have” to get a hood instead. This is obviously bogus.
This also leads to the inevitable Contractor Special where a duct was there, often when the user is replacing an old hood with a microwave, but the installer just shrugs and slaps the microwave on the wall as-is where A) it is inevitably too tall and now way too close to the stovetop, and B) covering the duct outlet while still recirculating back into the room. Whenever I unearth one of these in my travels it makes me want to track down whoever the hell installed it and then punch them so hard they come clean out of their socks.
People are for some reason hyperfixated on getting appliances off of their countertops, which is why the over-the-range microwaves became so prevalent in the first place. (And then they all immediately filled the spot where their countertop microwave used to be with a countertop air fryer instead, but that’s a whole different discussion.)
Yeah that would drive me insane to run across. It’s not even particularly hard to tell that the exhaust fan motor is reversible just by looking at the top/back of the microwave before it is installed. Every one I’ve seen looks pretty damn modular in comparison to the rest of the microwave shell.
Edit: reversible is the wrong word, able to be unscrewed and rotated, I’m sure you know what I meant but on a reread of my comment I wanted to clarify.